Gas service - Emergency Boiler Breakdown Repair and Maintenance
We know it’s real horrible experience if your boiler or central heating has broken down when the weather the freezing cold. It really can give you headache!
However you have our company here to get you out of this situation.
We are a GAS SAFE registered Company (used to be called Corgi); London plumber with 15 years experience, covering all Central London (City London), West End London (West), South West London, North London, North West London, South East London, East London, Enfield, Essex, Kent, Bromley & Kent, Twickenham and all surrounding areas
At our company – we have commercial & domestic gas engineers who are qualified and are gas safe corgi engineers who deal with all types of gas boiler maintenance all emergency corgi plumbers have experience to repair, maintenance and install all gas and electric boilers like Worcester Bosch combi boilers, Greenstar 28i Junior, Greenstar 24i junior, condensing combi boilers, combi boiler installation, baxi condensing boiler, condensing combination boilers, , biasi boilers , central heating combi boilers, Baxi megaflo, condenser boilers, Vaillant boilers, Alpha boilers, Cheating installation, Biasi boiler, and other types of boilers
Our recommended commercial heating engineers are registered and qualifies to do central heating installations even under floor heating system repair and installations they are also heating contractors who take on all work in commercial buildings, offices, homes. When you have problems with heating or plumbing we have heating plumbing specialists who can assist you with heating repair, heating breakdown and some time your heating may be broken because it needs to part like gas filter, gas heat pump , gas valve repair, thermocouple repair, gas boiler spares as they can be important parts that are needed in order to get the heating working
Condensing Boliler - Get Your Boiler Repaired by Recommended Gas Safe Registered Engineer
Combination boilers and system boilers both carry pressure gauges and we're often asked about the pressure shown on these gauges. Any sealed central heating system needs an expansion vessel, a pressure gauge and a pressure relief safety valve.
If you heat water it expands. In an open vented central heating system (with a header tank) some of the water moves back up into the header tank. The expansion does not increase the overall volume of water by a huge amount (maybe 3 or 4 litres, depending on the size of the heating system) but it would be more than enough to burst the pipes if it had nowhere to go.
In a sealed system you have to allow for this expansion. This is done by adding an expansion vessel to the system pipework and it's often inside the boiler. The expansion vessel is just a chamber with a rubber diaphragm across the middle. One side of the expansion chamber is connected to the system pipework. The other side has a car tyre type valve so it can be pumped full of air.
In manufacture the air side is pumped full of air, typically to about 1 bar (about 15 psi). This forces the diaphragm right across to the opposite wall of the chamber. When the central heating system is filled with water and pressurised (to about 1 bar) the water pushes the diaphragm back to about the middle
Get to know "Gledhills BoilerMate"
BoilerMates are thermal stores, in other words a tank full of water heated by an ordinary central heating boiler. The water never changes. It is used purely to store heat energy from the boiler. The stored hot water is pumped around the radiators top heat the house, and is used to heat domestic tap water before it arrives at the hot taps. This allows hot water to taps and showers at full mains pressure for high performance showering and faster bath filling.
The boilermate is very similar to the SysteMate and the two are easily confused. The difference is that the Boilermate pumps the thermal store water around the radiators directly, meaning radiators cannot be installed at a higher level than the BoilerMate cistern. The SysteMate separates the central heating water from the thermal store water using a copper heating coil inside to transfer heat from the boiler primary into the thermal store water, allowing use of a sealed heating system and location of the SysteMate becomes free
We know that it is a huge problem finding right and honest trade’s people including good plumber’s and gas engineer’s in London and even in the surrounding areas. Especially, during the “Current climate”- you don’t want to spend money on something if you don’t know if it will be worthwhile. Don’t panic! A reliable company like us are here to change this. We are offering the benefits of the knowledge we have to give “YOU” the customer the right advice – this will result in you saving hundreds or even thousands of pounds in some cases. This is for your benefit.
